BlogHotel.orgAccueil | Créer un blog | Imprimer la page Imprimer | Blog hasard Au hasard | Chercher des blogs Rechercher | Entrer dans le chat du blog Chat | | Jeux Jeux | Adminitration et édition du Blog Manager

wisepowder Accueil | Profil | Archives | Amis
wisepowder

WHAT IS A PNEUMATIC ACTUATED VALVE?29/3/2022
WHAT IS A PNEUMATIC ACTUATED VALVE? Pneumatic actuated valves used compressed air flowing into and exhausting from an actuator to open and close the valve. The type of pneumatic actuator required depends on the actuator valve. Valves requiring linear motion (gate, globe or diaphragm valves) typically require a pneumatic diaphragm actuator. Quarter turn valves (ball and butterfly valves) typically require either a rack-and-pinion actuator or a scotch yoke actuator. We'll discuss the two types on quarter-turn air actuators in greater detail.Get more news about pneumatic actuated valve,you can vist our website! Scotch yoke actuators are composed of a piston directly connected to a slotted yoke. A pin on the rotating shaft rides in the yoke slot, converting the linear motion to rotational motion in much the same way a crankshaft converts the linear motion of a piston connecting rod. Scotch yoke actuators have a nonlinear torque profile, with the highest torque at the beginning and end of the stroke. Scotch yoke construction is readily scale-able, making this type of actuator suitable for large pneumatic actuator valves requiring high torque. Rack-and-pinion actuators use a piston to drive a toothed shaft (the rack) which is geared to the actuator output drive (the pinion). They are typically used in lower torque applications, offer a more precise control and an even torque throughout the stroke. For purposes of this discussion, we'll focus on quarter turn actuators. Pneumatic quarter turn actuators operate in two different modes: double acting and spring return. Double Acting Double acting actuators use compressed gas driving a piston to both open and close the valve. These actuators have two ports to pass and exhaust the gas. Compressed gas is fed through the first port, causing the actuator to close the valve, and then exhausted out the second port. To return to the original position the supply and exhaust functions are reversed. Spring Return Spring return actuators typically have a single port to both pass and exhaust the compressed gas. Unlike double acting actuators, spring return actuators are driven in a single direction and, when the gas is exhausted, use springs to return to the original position. The valve can be installed to return to either the closed or open position; the more common mode is normally closed. Controlling Pneumatic Actuators As we've seen, actuators with pneumatic action require compressed air to be supplied and exhausted at certain ports at certain times. In the case of double acting actuators, both ports serve as supply and exhaust ports depending on actuator position, and for spring return actuators a single port serves as both the supply and exhaust port. This necessitates some sort of external switching. This is often accomplished via an external bank of pilot valves. An electronic controller (like a PLC) opens and closes pilot valves which in turn actuate the main air pneumatic valves. However, in large plants or outdoor applications the valve bank may be far from the actuator. In this case long runs of small-diameter pneumatic lines are impractical due to the line pressure loss and the potential for leaks at connections. Instead, it is preferable to run electrical wires directly to the valve and control the valve locally. Compressed pilot air may be supplied by a short run from the piping of the main plant. Direct mount pilot valves accomplish this by using an electrically actuated solenoid valve to control the compressed gas. The solenoid valve mounts directly to the pneumatic actuator. When energized, the solenoid moves a plunger which directs compressed gas into or out of the valve depending upon configuration. Double-acting air actuator valves are controlled by solenoid valves utilizing a five port, two position (or 5/2) configuration. The five ports are two output, two exhaust and one input. For spring return control solenoid valves use a 3/2 configuration (one output, one exhaust, one input).
Poster un Commentaire

Entry 1579 of 2891
Précédent | Suivant

Blog suivant >> Signaler un abus?Haut de page